MFP CONSTRUCTION BOARD – TECHNIQUE AND APPLICATION:<\/strong><\/em><\/p>\n1. Floor and ceiling<\/p>\n
MFP boards are laid perpendicularly or parallel to the floor beams, maintaining the offset \u00bd of the board relative to each other. Expansion joints are kept between 3-6 mm wide boards and must be filled with a\u00a0flexible wood mass (e.g. glue). A\u00a012 mm wide expansion gap should be maintained from the wall itself. MFP boards are insulated from floor beams. When laying larger surfaces (over 12 running meters), it is recommended to prepare additional 2.5 mm wide expansion joints for all panel joint edges (min. 1 mm tongue and groove panels on unprinted \/ base surfaces) regardless of the gap behavior. a\u00a0wall; it is recommended to fill such expansion joints with an elastic mass (e.g. glue) intended for wood.<\/p>\n
MFP Construction Boards<\/h2>\n
For 22 mm thick boards, regular and spiral nails with a\u00a0minimum length of 51 mm or fluted nails with a\u00a0minimum length of 45 mm are ideal. It is also possible to use screws (type SPAX 4×35) with a\u00a0thread length of 35 mm.<\/p>\n
A\u00a0maximum of max. Between screws, nails and screws must be kept. distance of 150 mm at the extreme edges and max. distance 300 mm in the center of the plate. We avoid tearing the panel at the edges while maintaining a\u00a0minimum distance from the edge of 8 mm. Similarly, a\u00a0minimum distance of 16 mm should be maintained in the corners (16 mm and 32 mm for tongue and groove panels).<\/p>\n
2. Walls<\/p>\n
It is recommended to use 12-15 mm thick panels on the outer wall sheathing and 10 mm thick panels inside the building. MFP boards are laid on the walls vertically or horizontally, using a\u00a0shift of min. 1\/3 of the disc relative to each other. Keep expansion joints 3-6 mm wide. Joints are not filled. Additional expansion joints should be used between the MFP board and the foundation and on the coronary beam.<\/p>\n
When laying larger surfaces (over 12 linear meters) from MFP boards, it is worth making an additional 2.5 mm wide expansion joint on all edges of the board connection (in MFP boards of the tongue and groove minimum 1 mm for unprinted \/ base surfaces) regardless of the behavior wall cracks.<\/p>\n
For 12 mm thick boards, regular and spiral nails with a\u00a0minimum length of 51 mm or corrugated nails with a\u00a0minimum length of 45 mm are ideal. It is also possible to use screws (type SPAX 4×35) with a\u00a0thread length of 23 mm.<\/p>\n
A\u00a0maximum of max. Between screws, nails and screws must be kept. distance of 150 mm at the extreme edges and max. distance 300 mm in the center of the plate. We avoid tearing the panel at the edges while maintaining a\u00a0minimum distance from the edge of 8 mm. Similarly, a\u00a0minimum distance of 16 mm should be maintained in the corners (16 mm and 32 mm for tongue and groove panels).<\/p>\n
A\u00a0maximum of max. Between screws, nails and screws must be kept. distance of 150 mm at the extreme edges and max. distance 300 mm in the center of the plate. We avoid tearing the panel at the edges while maintaining a\u00a0minimum distance from the edge of 8 mm. Similarly, a\u00a0minimum distance of 16 mm should be maintained in the corners (16 mm and 32 mm for tongue and groove panels). The thickness of MFP panels should be adjusted to the rafter spacing, parameters of panel deflections, type and slope of the roof slope.<\/p>\n","protected":false},"excerpt":{"rendered":"
MFP Construction Boards<\/h3>\n
MFP boards should be laid perpendicular or parallel to the rafters, staggered with a 1\/3 offset of the board relative to each other. They should be connected with steel H connectors. 3-6 mm wide expansion joints must be maintained between the panels. An additional 25 mm wide gap is recommended to be used on all edges connecting MFP boards (for tongue and groove boards, 1 mm on unprinted \/ base surfaces is enough) regardless of the extent of the gap near the wall<\/p>\n","protected":false},"featured_media":727,"comment_status":"open","ping_status":"closed","template":"","meta":{"_et_pb_use_builder":"","_et_pb_old_content":""},"product_brand":[],"product_cat":[29],"product_tag":[],"class_list":{"0":"post-726","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-osb-board","8":"first","9":"instock","10":"shipping-taxable","11":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/product\/726","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/comments?post=726"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/media\/727"}],"wp:attachment":[{"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/media?parent=726"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/product_brand?post=726"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/product_cat?post=726"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pomar-sc.com\/index.php\/wp-json\/wp\/v2\/product_tag?post=726"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}